Phone:0710-3552030、13871636870
产品属性

1:1 Two Component Silicone Potting Compound

广东省某某某科技有限公司
联系方式: 13622225555
官方微博: 广东某某有限公司
地址: 广东省珠海市香洲区XXX街道666号8楼233室
产品介绍

Taisn Two Component Silicone Potting Compound, Mix Ratio is A:B=1:1


Product features:


1, After mixing, the potting compound resting period is long, and curing time can be fast if with heat treatment, so it’s very good to be used in automatic production line.

2, This product has good high temperature resistance and ageing resistance. It can keep good elastic and insulation performance after curing from -60~250℃. 

3,The compound won’t shrink when curing, it has excellent ageing resistance and water-proof.

4, It has good thermal conductivity and flame retardancy. Flame resistance can reach UL94-V1.



Product application:


This product is designed for potting and protecting high power electronic components, module power supply and PCB which request good heat dissipation and high temperature resistance. For example, automobile HID lamp module power supply, automotive ignition system module power supply, solar panels, transformer and sensor etc.


Technical Data Sheet:


Before curing

Appearance

White(A)/White(B)liquid

Viscosity(cps,25℃)

3000~5000

Mix ratio

A :B = 1 :1

Viscosity after mixing (cps)

2500~4500

Operational time(min,25℃)

40

Curing time(min,25℃)

360

Initial curing time(min,25℃)

120

After curing

Hardness (shore A)

40±5

Thermal conductivity [ W(m·K)]

≥0.8

Dielectric strength(kV/mm)

≥27

Dielectric constant(1.2MHz)

3.0~3.3



Volume resistivity (Ω·cm)

≥1.0×1016

Coefficient of linear expansion [m/(m·K)]

≤2.2×10-4

Flame resistance

94-V1

Waterproof grade

≥IP67



How to use:


1): Mix two parts in a container by ratio of A: B=1:1, then stir two parts uniformly.

2): Pour the mixed compound to the parts to be potting. Normally it doesn’t need vacuum defoaming. If need get high thermal conductivity, we suggest to use vacuum defoaming before potting. The potting compound can cure at room temperature or thermal curing. Curing speed is related to temperature, it need long time to cure in winter, then we suggest to use thermal curing. At 80℃ the curing time is only 10-20 minutes, at room temperature curing time is 6-8 hours.


Attention:

The potting compound should be stored in sealed condition. Use up the mixed compound one time to avoid wasting.

This product is non-toxic, but avoid swallow or contact eyes.

After long storage, the potting compound additive will subside, then stir them uniformly before using, and it won’t affect the performance.


Note, the potting compound will not cure if contact with below chemical substances:

1: N, P, S organic compound

2: Sn, Pb, Hg, As plasma compounds

3: Alkynes and polyvinyl compounds


Taisn Two Component Silicone Potting Compound, Mix Ratio is A:B=1:1


Product features:


1, After mixing, the potting compound resting period is long, and curing time can be fast if with heat treatment, so it’s very good to be used in automatic production line.

2, This product has good high temperature resistance and ageing resistance. It can keep good elastic and insulation performance after curing from -60~250℃. 

3,The compound won’t shrink when curing, it has excellent ageing resistance and water-proof.

4, It has good thermal conductivity and flame retardancy. Flame resistance can reach UL94-V1.



Product application:


This product is designed for potting and protecting high power electronic components, module power supply and PCB which request good heat dissipation and high temperature resistance. For example, automobile HID lamp module power supply, automotive ignition system module power supply, solar panels, transformer and sensor etc.


Technical Data Sheet:


Before curing

Appearance

White(A)/White(B)liquid

Viscosity(cps,25℃)

3000~5000

Mix ratio

A :B = 1 :1

Viscosity after mixing (cps)

2500~4500

Operational time(min,25℃)

40

Curing time(min,25℃)

360

Initial curing time(min,25℃)

120

After curing

Hardness (shore A)

40±5

Thermal conductivity [ W(m·K)]

≥0.8

Dielectric strength(kV/mm)

≥27

Dielectric constant(1.2MHz)

3.0~3.3



Volume resistivity (Ω·cm)

≥1.0×1016

Coefficient of linear expansion [m/(m·K)]

≤2.2×10-4

Flame resistance

94-V1

Waterproof grade

≥IP67



How to use:


1): Mix two parts in a container by ratio of A: B=1:1, then stir two parts uniformly.

2): Pour the mixed compound to the parts to be potting. Normally it doesn’t need vacuum defoaming. If need get high thermal conductivity, we suggest to use vacuum defoaming before potting. The potting compound can cure at room temperature or thermal curing. Curing speed is related to temperature, it need long time to cure in winter, then we suggest to use thermal curing. At 80℃ the curing time is only 10-20 minutes, at room temperature curing time is 6-8 hours.


Attention:

The potting compound should be stored in sealed condition. Use up the mixed compound one time to avoid wasting.

This product is non-toxic, but avoid swallow or contact eyes.

After long storage, the potting compound additive will subside, then stir them uniformly before using, and it won’t affect the performance.


Note, the potting compound will not cure if contact with below chemical substances:

1: N, P, S organic compound

2: Sn, Pb, Hg, As plasma compounds

3: Alkynes and polyvinyl compounds